Mg gas infiltration for the fabrication of MgB2 pellets using nanosized and microsized B powders

MgB₂ superconductor pellets were synthesized through Mg gas infiltration method using nanosized- and microsized B powders. There was a marked difference in the superconducting properties of the two samples, particularly in the pinning force and dominant pinning mechanism. The microstructures of the samples were observed using HR-TEM and STEM-HAADF, and the results showed that the primary reason for the difference in the superconducting properties is the distribution of the nanosized second-phase particle MgO. Additionally, a feasible reaction model for the Mg gas infiltration method was established. Compared to the Mg liquid infiltration method, the gas infiltration showed better penetrability ability with a small amount of residual Mg. This study presents a novel synthesis process to fabricate an MgB₂ pellet with superior density and superconducting properties. This method can be used in multiple applications such as superconducting bearings, compact superconductor magnets, and magnetic shielding.     

Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

Alumina ceramics with different unit numbers and gradient modes were prepared by digital light processing (DLP) 3D printing technology. The side length of each functional gradient structure was 10 mm, the porosity ratio was controlled to 70%, and the number of units were (1 × 1 × 1 unit) and (2 × 2 × 2 unit) respectively. The different gradient modes were named FCC, GFCC-1, GFCC-2 and GFCC-3. SEM, XRD, and other characterization methods proved that these gradient structures of alumina ceramics had only α-Al2O3 phase and good surface morphology. The mechanical properties and energy absorption properties of alumina ceramics with different functional gradient structures were studied by compression test. The results show that the gradient structure with 1 × 1 × 1 unit has better mechanical properties and energy absorption properties when the number of units is different. When the number of units is the same, GFCC-2 and GFCC-3 gradient structures have better compressive performance and energy absorption potential than FCC structures. The GFCC-2 gradient structure with 1 × 1 × 1 unit has a maximum compressive strength of 19.62 MPa and a maximum energy absorption value of 2.72 × 105 J/m3. The good performance of such functional gradient structures can provide new ideas for the design of lightweight and compressive energy absorption structures in the future.     

A numerical study of dynamic behaviors of a unitized regenerative fuel cell during gas purging

The gas purging states affect electricity output and energy storage capacity of unitized regenerative fuel cells. In this study, a model of unitized regenerative fuel cell is established. Cell voltages and operating temperatures influences on the dynamic distribution of thermal fluid during purging process and the discharge of residual liquid water in electrolytic cell mode are investigated. The motivation of the present study is better understanding the gas purging characteristics and its effect on reaction behaviors of unitized regenerative fuel cells. Simulation results reveal a significant influence of purging gas temperature on the water flooding and a great effect of operating voltage on the water diffusion. The operating temperature of electrolytic cell model almost has little effect on purging results at different cell temperature and the same purging gas temperature. When the purging gas temperature is changed, higher temperatures of cell and purging gas facilitate liquid water discharging out from the cell regions. In cell water flooding situation, when having large liquid content, the purging gas has little effects on the water expelling process.     

碱铝硅酸盐玻璃化学强化关键影响因素概述

化学强化是一种玻璃机械强度增强方法,适用于异型、超薄、高碱、高膨胀玻璃增强,因新型超薄显示产品的屏幕保护玻璃发展需要,化学强化技术重新在碱铝硅酸盐玻璃品种掀起研究热潮。本文对化学强化本质及铝硅酸盐玻璃在屏幕保护玻璃应用进行了回顾,基于玻璃化学强化的高CS、DOL和低CT诉求,归纳总结了关键影响因素,第1,碱铝硅酸盐玻璃的成分及结构是基础,氧化铝有利玻璃网络孔隙增大创造交换通道,氧化钠或氧化锂是离子交换关键物质;第2,对于玻璃组成和结构设计,要求玻璃网络键合度R=O/Si或O/(Si+Al)满足2.15~2.40,碱金属氧化物质量分数大于13%且膨胀系数大于6×10^-6/℃;第3,在化学强化工艺方面,化学强化温度决定离子扩散系数,化学强化时间决定DOL,一步法仅能获得相对较大的CS,而DOL不很理想,只有两种离子参与交换的二步法才有利于CS和DOL同步提高。     

车用有机朗肯循环系统中计量泵的性能研究

在模拟车用有机朗肯循环(organic Rankine cycle,ORC)系统的工作环境下,设计并搭建以R123作为工质的液压隔膜计量泵性能测试平台。在额定转速(2900 r/min)下,通过调节液压隔膜计量泵的冲程(25%、50%、75%、100%)和出口压力,得到变工况下液压隔膜计量泵的特性曲线,并分析液压隔膜计量泵的关键参数对车用ORC系统性能的影响情况。结果表明:液压隔膜计量泵的流量受冲程影响,与出口压力基本无关。其输入功率和实际运行效率均随着冲程的增加而升高,最高分别可达523.91 W、88.27%。应用该液压隔膜计量泵的模拟车用ORC系统吸热量变化范围较广,系统热效率最高可达12.81%。液压隔膜计量泵可应用于车用ORC系统,通过调节液压隔膜计量泵的冲程和出口压力,可实现提高车用ORC系统热效率、增加系统净输出功率的目的。     

Machining accuracy improvement for a dual-spindle ultra-precision drum roll lathe based on geometric error analysis and calibration

This paper performs a comprehensive analysis and calibration on the geometric error of the ultra-precision drum roll lathe with dual-spindle symmetrical structure and cross slider layout. Firstly, the volumetric error model which contains all geometric errors of the dual-spindle ultra-precision drum roll lathe (DSUPDRL) is developed based on the combination of the homogenous transfer matrix (HTM) and multi-body system (MBS) theory. Secondly, sensitivity analysis for the volumetric error model is conducted to identify the sensitive geometric error components of the DSUPDRL using an improved Sobol method based on the quasi-Monte Carlo algorithm. The result of sensitivity analysis laid the foundation for the subsequent geometric error calibration. Then, some sensitive error components along the X and Z directions are calibrated using a laser interferometer and a pair of inductance displacement probes. Besides the volumetric error model, the concentricity error caused by dual-spindle symmetrical structure is proposed and calibrated by the on-machine measurement using a classic reversal method. Finally, a large-scale roller mold with a diameter of 250 mm and a length of 600 mm is machined using the DSUPDRL after calibration. The experimental result shows that 1.4 μm/600 mm generatrix accuracy is obtained, which validate the effectiveness of the geometric error analysis and calibration.     

Elastic modulus of nanocrystalline cemented carbide

The purposes of this work were to obtain the accurate elastic modulus of the nanocrystalline WC–Co cemented carbides, and to propose the mechanism for the difference of elastic modulus between the nanocrystalline and conventional polycrystalline cemented carbides. The nanocrystalline cemented carbide was prepared by spark plasma sintering (SPS) technique. The conventional polycrystalline cemented carbides were prepared by SPS and sinter-HIP techniques as references, respectively. The sintered cemented carbides were characterized by X-ray diffractometry, scanning electron microscopy and the transmission electron microscopy with precession electron diffraction technology. The elastic modulus was obtained by averaging the values measured with the continuous stiffness measurement method of the nanoindentation technology. The results show that the nanocrystalline cemented carbide has a relatively low modulus, which could be attributed to the more interface area and higher fraction ratio of the hcp cobalt phase caused by the rapid heating and cooling process during SPS.     

SLM printing of cermet powders: Inhomogeneity from atomic scale to microstructure

It is very challenging for 3D printing based on the selective laser melting (SLM) technology to obtain cermet bulk materials with high density and homogeneous microstructures. In this work, the SLM process of the cermet powders was studied by both simulations and experiments using the WC-Co cemented carbides as an example. The results indicated that the evolution of the ceramic and metallic phases in the cermet particle during the heating, melting and solidification processes were all significantly inhomogeneous from atomic scale to mesoscale microstructures. As a consequence, the microstructural defects were caused intrinsically in the printed bulk material. The formation and growth of the bonding necks between the particles were mainly completed at the later stage of laser heating and the early stage of solidification. Both simulations and experiments demonstrated that thin amorphous layers formed at the ceramics/metal interfaces. This work disclosed the mechanisms for the evolution from the atomic scale to microstructure during the SLM printing of cermet powders, and discovered the origin of the defects in the printed cermet bulk materials.